Finoric LLC

Nomul Non-Emulsifier for Brines

NE118 Non Emulsifier Supplier Manufacturers and Manufacturers' Representative

FInOrIC, etymologically derived from our business line of Fine Inorganic, Organic and Industrial Chemicals, is the internationally preferred source for Chemicals. With customers in 55 countries across 5 continents, we source and sell most chemicals. Backed by owned full fledged chemical manufacturing facilities in Midland & Houston Area Texas with associated manufacturing sites in India, Dubai, China and USA we are a truly multi-national chemical manufacturer & distributor. Fracturing and Fracking Industry can rely on our 24x7 - 365days service including week-end deliveries.

DESCRIPTION

NOMUL is a proprietary formulation of blended non-ionic and amphoteric surfactants added into the completion or workover fluids to reduce the emulsion tendency of fluids with residual oils in the formation. Completion or workover fluids can form emulsions with the residual oil in the formation during or after workover or stimulation treatments. These emulsions may remain strongly associated with the formation and can impede flow and reduce productivity. The main function of NOMUL is to break such an emulsion in-situ before the stimulated well is put back to production. Another function of NOMUL is to speed up the separation of water and oil from the initial well flow-back.

Advantages
Totally miscible in all monovalent and calcium brines
Minimally absorbing surfactant blend
Helps lower surface tension of brines
Helps lower interfacial tension
Effective at low concentrations
Effective for both oil and gas production
Helps maximize completion or workover fluid recovery
Cost effective

Typical Physical Properties
Characteristic Specification
Appearance Clear, Light yellow
Viscosity 64 - 65 cP
pH 3.5
Specific gravity 1.02 @ 75F

Dosage
The treat rate of the NOMUL is 1.0 – 2.0% by volume in the brine. Testing with the produced crude is recommended to optimize treatment.

Performance Testing
Compatibility tests conducted with standard non-emulsion tests in which a 50/50 mixture of crude oil and selected brine (with and without NOMUL) was mixed under low-shear conditions in a glass bottle and allowed to stand in a hot water-bath at 150° F.
For these tests, compatibility is defined by a 95% phase separation within 30 min at a specified temperature. In addition, brine wettability is evaluated by observing the interaction of the brine and the surface of the glass bottle. Poor wettability is considered evident if the brine "clings" to the glass and does not freely move along its surface. The interface between brine and oil is also inspected, whereby the most effective system is one providing the most distinct phase separation.
Brines tested were 9.5 ppg NaCl, 12.0 NaBr, 11.0 ppg CaCl2 and 13.0 ppg CaBr2. Texas Raw Crude was used for the oil phase. All samples were treated with 1% diluted NOMUL. The results are shown below.

Emulsion Control

Emulsion tendency controlled with NOMUL treatment.

Storage and Handling
NOMUL is available in 55 gallon drums and 330 gallon totes. As with any industrial chemical, avoid prolonged contact with skin and eyes. In case of skin or eye contact, flush the exposed area with copious amounts of water. A safety data sheet outlining proper handling of this product is available upon request.

Availability
Global from Houston, TX-USA, Midland, TX-USA, Dubai, UAE, and Mumbai, India.


Most of our partners facilities of MANUFACTURE BULK DRUGS/API, EXCIPIENTS, PHARMACEUTICALS (IP/BP/USP/NF/PH. EUR./JP), SPECIALITY CHEMICALS (PURE/AR/ACS), MINERAL FORTIFIERS (FCC). OUR MANUFACTURING FACILITY IS GLP, GMP (FDA) APPROVED, ISO 9001, ISO 14001, ISO 22000, FSSC 22000, FSSAI, KOSHER, HALAL, COPP AND WHO-GMP CERTIFIED.

Good Manufacturing Practice Certified by World Health Organization (WHO-GMP)
Written Confirmation Certification (WC)
Good Manufacturing Practice (cGMP)
Good Laboratory Practice (GLP)


Finoric LLC