Finoric LLC

Urea

CAS Number 57-13-6, Urea USP BP ACS FCC Food Analytical Reagent Grade Supplier, Manufacturer's Representative

CAS number : 57-13-6
Chemical Formula: CH4N2O

FInOrIC, etymologically derived from our business line of Fine Inorganic, Organic and Industrial Chemicals, is the internationally preferred source for Chemicals. With customers in 55 countries across 5 continents, we source and sell most chemicals. Backed by owned full fledged chemical manufacturing facilities in Midland & Houston Area Texas with associated manufacturing sites in India, Dubai, China and USA we are a truly multi-national chemical manufacturer & distributor. Fracturing and Fracking Industry can rely on our 24x7 - 365days service including week-end deliveries.

DESCRIPTION

Urea USP
Formula: CH4N2O
Weight: 60.06
Urea.
Carbamide.

Urea contains not less than 99.0 percent and not more than 100.5 percent of CH4N2O.
Labeling: Where it is intended for use in preparing injectable dosage forms, the label states that it is sterile or must be subjected to further processing during the preparation of injectable dosage forms.

Identificationg:
A: Heat about 500 mg in a test tube: it liquefies, and ammonia is evolved. Continue the heating until the liquid becomes turbid, then cool. Dissolve the fused mass in a mixture of 10 mL of water and 1 mL of sodium hydroxide solution (1 in 10), and add 1 drop of cupric sulfate TS: the solution acquires a reddish-violet color.
B: Dissolve 100 mg in 1 mL of water, and add 1 mL of nitric acid: a white crystalline precipitate of urea nitrate is formed.
Melting rangeg: between 132 and 135.
Residue on ignitiong: not more than 0.1%.
Alcohol-insoluble matterg: 0.04%.
Chlorideg: 0.007%.
Sulfateg: 0.010%.
Heavy metalsg: the limit is 0.002%.
Other requirementsg: Where the label states that Urea is sterile, it meets the requirements for Sterility Tests 71 and for Bacterial endotoxins under
Urea for Injectiong: Where the label states that Urea must be subjected to further processing during the preparation of injectable dosage forms, it meets the requirements for Bacterial endotoxins under Urea for Injection.

Urea BP
Formulag: CH4N2O
Weightg: 60.1
CAS Numberg: 57-13-6

DEFINITION
Carbamide
Contentg: 98.5 per cent to 101.5 per cent (dried substance).

CHARACTERS
Appearanceg: White or almost white, crystalline powder or transparent crystals, slightly hygroscopic.
Solubilityg: Very soluble in water, soluble in alcohol, practically insoluble in methylene chloride.

IDENTIFICATION
First identification A, B.
Second identification A, C, D.
A. Melting point: 132C to 135C.
B. Infrared absorption spectrophotometry.
C. Dissolve 0.1 g in 1 ml of water. Add 1 ml of nitric acid. A white, crystalline precipitate is formed.
D. Heat 0.5 g in a test tube until it liquefies and the liquid becomes turbid. Cool, dissolve in a mixture of 1 ml of dilute sodium hydroxide solution and 10 ml of water and add 0.05 ml of copper sulphate solution. A reddish-violet colour is produced.

TESTS
Solution Sg: Dissolve 10.0 g in water and dilute to 50 ml with the same solvent.
Appearance of solutiong: The solution is clear and colourless.
To 2.5 ml of solution S add 7.5 ml of water.
Alkalinityg: To 2.5 ml of solution S add 7.5 ml of water, 0.1 ml of methyl red solution and 0.4 ml of 0.01 M hydrochloric acid . The solution is red to orange.
Biuretg: Maximum 0.1 per cent.
Ammoniumg: Maximum 500 ppm, determined on 0.1 ml of solution S.
Heavy metalsg: Maximum 10 ppm.
Loss on dryingg: Maximum 1.0 per cent, determined on 1.000 g by drying in an oven at 105C for 1h.
Sulphated ashg: Maximum 0.1 per cent, determined on 1.0 g.

Urea FCC
Carbamide
Formula: CH4N2O
weight: 60.06
CAS Number: 57-13-65

DESCRIPTION
Urea occurs as a colorless to white, prismatic, crystalline powder or as small, white pellets. It is commonly produced from CO2 by ammonolysis or from cyanamide by hydrolysis. It is freely soluble in water and in boiling alcohol, but practically insoluble in chloroform and in ether. It melts at a range of 132° to 135°.
Function Fermentation aid.

REQUIREMENTS
Identification:
A. Heat about 500 mg of sample in a test tube until it liquefies. Ammonia vapor is produced. Continue heating until the liquid becomes turbid, and then cool. Dissolve the fused mass in a 1:10 sodium hydroxide solution:water mixture. Add 1 drop of cupric sulfate TS. A red-violet colored solution develops.
B. Dissolve 100 mg of sample in 1 mL of water, and add 1 mL of nitric acid. A white precipitate of urea nitrate forms.
Assay: Not less than 99.0% and not more than 100.5% of CH4N2O.
Alcohol-Insoluble Matter: Not more than 0.04%.
Chloride: Not more than 0.007%.
Lead: Not more than 5 mg/kg.
Loss on Drying: Not more than 1.0%.
Residue on Ignition: Not more than 0.1%.
Sulfate: Not more than 0.01%.

Urea ACS
Formula: NH2CONH2
Weight: 60.06
CAS Number: 57-13-6

REQUIREMENTS
Assay: 99.0-100.5%
Melting point: 132-135C

MAXIMUM ALLOWABLE
Insoluble matter: 0.01%
Residue after ignition: 0.01%
Chloride (Cl): 5 ppm
Sulfate (SO4): 0.001%
Heavy metals (as Pb): 0.001%
Iron (Fe): 0.001%


Most of our partners facilities of MANUFACTURE BULK DRUGS/API, EXCIPIENTS, PHARMACEUTICALS (IP/BP/USP/NF/PH. EUR./JP), SPECIALITY CHEMICALS (PURE/AR/ACS), MINERAL FORTIFIERS (FCC). OUR MANUFACTURING FACILITY IS GLP, GMP (FDA) APPROVED, ISO 9001, ISO 14001, ISO 22000, FSSC 22000, FSSAI, KOSHER, HALAL, COPP AND WHO-GMP CERTIFIED.

Good Manufacturing Practice Certified by World Health Organization (WHO-GMP)
Written Confirmation Certification (WC)
Good Manufacturing Practice (cGMP)
Good Laboratory Practice (GLP)


Finoric LLC